What is a transaction identifier?Question 20Select one:a.It is the unique identifier of the transaction that performed the read operation.b.It is the unique identifier of the transaction that performed the write operation.c.It is the unique identifier of the transaction that performed the delete operation.d.It is the unique identifier of the transaction that performed the commit operation.e.It is the unique identifier of the transaction that performed the stop operation.

Which of the given options define a transaction correctly?A transaction consists of COMMIT or ROLLBACK in a database session.A transaction consists of either a collection of DML statements or a DDL or DCL or TCL statement to form a logical unit of work in a database session.A transaction consists of DDL statements on the database schema.A transaction consists of collection of DML and DDL statements in different sessions of the database.

Transaction States and Additional OperationsA transaction is an atomic unit of work that should either be completed in itsentirety or not done at all. For recovery purposes, the system needs to keep track ofwhen each transaction starts, terminates, and commits or aborts (see Section21.2.3). Therefore, the recovery manager of the DBMS needs to keep track of thefollowing operations:■ BEGIN_TRANSACTION. This marks the beginning of transaction execution.■ READ or WRITE. These specify read or write operations on the databaseitems that are executed as part of a transaction.■ END_TRANSACTION. This specifies that READ and WRITE transaction oper-ations have ended and marks the end of transaction execution. However, atthis point it may be necessary to check whether the changes introduced by752 Chapter 21 Introduction to Transaction Processing Concepts and TheoryActiveBegintransactionEndtransaction CommitAbortAbortRead, WritePartially committedFailed TerminatedCommittedFigure 21.4State transition diagram illustrating the states fortransaction execution.the transaction can be permanently applied to the database (committed) orwhether the transaction has to be aborted because it violates serializability(see Section 21.5) or for some other reason.■ COMMIT_TRANSACTION. This signals a successful end of the transaction sothat any changes (updates) executed by the transaction can be safelycommitted to the database and will not be undone.■ ROLLBACK (or ABORT). This signals that the transaction has ended unsuc-cessfully, so that any changes or effects that the transaction may have appliedto the database must be undone.Figure 21.4 shows a state transition diagram that illustrates how a transaction movesthrough its execution states. A transaction goes into an active state immediately afterit starts execution, where it can execute its READ and WRITE operations. When thetransaction ends, it moves to the partially committed state. At this point, somerecovery protocols need to ensure that a system failure will not result in an inabilityto record the changes of the transaction permanently (usually by recording changesin the system log, discussed in the next section).5 Once this check is successful, thetransaction is said to have reached its commit point and enters the committed state.Commit points are discussed in more detail in Section 21.2.3. When a transaction iscommitted, it has concluded its execution successfully and all its changes must berecorded permanently in the database, even if a system failure occurs.However, a transaction can go to the failed state if one of the checks fails or if thetransaction is aborted during its active state. The transaction may then have to berolled back to undo the effect of its WRITE operations on the database. Theterminated state corresponds to the transaction leaving the system. The transactioninformation that is maintained in system tables while the transaction has been run-ning is removed when the transaction terminates. Failed or aborted transactionsmay be restarted later—either automatically or after being resubmitted by theuser—as brand new transactions.5Optimistic concurrency control (see Section 22.4) also requires that certain checks are made at this

What is an identifier in C language?(1 Point)An identifier is a combination of alphanumeric characters used for conditional and control statementsAn identifier is a combination of alphanumeric characters used for any variable, function, label nameBoth A and BNone of the above

Transaction processing is associated with everything below except producing detail, summary, or exception reports. recording a business activity. maintaining data. confirming an action or triggering a response.

________________ is a unit of program execution that accesses and updates different data items in the database.a)Updationb)Insertionc)Manipulationd)Deletione)Transaction